There are two kinds of oven door locks. Some ovens have a lever-latch that allows you to manually lock the oven during long cook sessions. We’re not talking about this kind of oven door lock. Today, we’re here to talk about the automatic oven door lock that closes the oven during self-cleaning procedures and other oven functions. This is the automatic oven door lock assembly controlled by a small motor in the back of the oven. These designs can vary by model so we will be looking at a generalized replacement process that can usually work with all models.
There are several reasons you might want to replace your automatic oven door lock assembly. Perhaps you can’t clean your oven because the door lock won’t engage. Or perhaps you already cleaned your oven and now the door lock won’t unlatch so you can go on using the oven in a normal fashion. Or you may have experienced another more unique problem that indicates that the oven door lock assembly is at fault.No matter what your motivation, this guide will help you locate and replace the oven door lock assembly that controls the automatic lock on your oven door.
The first step when repairing or maintaining any electronic appliance is to pull the power plug. This ensures that no matter what happens, the oven can’t turn on while you’re working on it and you can’t get electrocuted or shocked by accident during the repair.
Disconnect the oven power cable from the wall to be certain your repair can be done in safety.
The automatic door lock assembly is located in the back of the oven, not the door itself. This means you’ll need access to the back of your oven so you’ll most likely need to pull the whole appliance away from the wall.
It is recommended that you get a friend to help you with this task. A piece of cardboard can protect the floor and make a decent temporary sliding aid. Carefully pull the range away from the wall until you have room to work behind it.
It may be necessary at this point to disconnect the power cable from the range unit in order to remove the back panel. Check your model of range to see if removing the power cable is necessary. If not, simply loop the cable out of your way for now.
Now you’ll need to remove the back panel to access the door lock assembly. The back panel will be attached with screws around the perimeter. Have a friend hold the panel into place as you remove the final screws so the panel does not torque as you are manning the screwdriver.
Carefully pull away and lower the back panel of your oven. You may want to place it on a towel or piece of cardboard on the floor nearby.
Your next task is to locate the door lock assembly for your model of oven. If you have done your homework and are prepared for the repair, no doubt you have a replacement part in hand. Look for the identical match to your replacement part inside the exposed back of your oven. This is the door lock assembly you’ll be replacing.
This is a very important step: Take a few photos of how the door lock assembly is installed, including the exact way the wires are attached. You may also or alternately want to use colored tape to clearly indicate where each wire connects.
The next step is to carefully remove the photoed and labeled wires from the broken door locking assembly. Because the oven is unplugged, this is safe to do without rubber gloves but you still want to treat the task gingerly. Remember where each wire came from and how they will connect to the new part.
Now you are ready to remove the broken door lock assembly.
Carefully remove the screws holding it into the housing and ease it out. You may have to tip the assembly back and pull it down to release it from mounting tabs. Don’t be afraid to be firm, or to use a light to investigate how the door lock assembly is held into place. Pulling out the old door lock assembly to throw away means it’s OK if you’re worried about being a little rough.
Remember how you got the old assembly out and reverse the processes to insert the new door lock assembly part. Carefully slot it into place, locking in any mounting tabs. Then reapply the screws each in the same place they came out of. This will ensure that your new door lock assembly is mounted firmly and correctly into place.
Refer to your photos and/or colored tape when attaching the control wires to the new door lock assembly. Photos are a great resource for being certain that the new assembly looks exactly like the old one did before it was removed. The tape will ensure that you can keep track of each individual wire in a real-world application while performing an unfamiliar repair.
With the mounting screws and wires in place, you have effectively replaced your oven’s automatic door lock assembly and it’s time to close back up. With the help of a friend, lift the back panel back into place and slot it in if necessary. Ask your friend to hold the back panel in place while you apply the screws around the perimeter. After about three screws, you should be able to continue without help. Secure the back panel firmly, tightening the screws so that there’s no risk of shaking.
You’re ready to put your oven and stove back into use. Now that your hands are out of the oven innards, it’s safe to plug the appliance back in and you may want to do this before you push the oven into place depending on where the outlet is. If you removed the cable, reattach it now. THen plug the oven back into the wall.
Finally, get the help of a friend to lift the oven off its floor covering and push it back into place between your counter sections. Congratulations, you have just fully replaced your automatic oven door lock assembly. Pat yourself on the back and test to see if your oven once again locks/unlocks as it’s supposed to.
If your Bosch dishwasher is displaying the E15 error code, this usually indicates excess water…
An unbalanced washing machine can lead to excessive noise and vibrations, which can reverberate around…
Gas stoves are great—they work even if you experience a power outage, and they’re widely…
It can be disappointing when the ice maker stops working as it's one of those…
If your Electrolux dryer is displaying the E64 error code, it usually indicates an issue…
An ice maker is one of those extra features that people are often prepared to…
Leave a Comment